Amplificazione finale Moduli
ST semiconductors a mos-fet, 80w/ch, distorsione < 1% a 6 ohms. Cablato con due
cavi dall’ampli ai terminali con il sistema Sigma Servo control per un migliore
smorzamento. Preamplificazione Ibrida con 1X 6922, tensione di uscita 6.5V con
2.0V input, impedenza <30 Ohms. Stadio finale in classe A, sul percorso del
segnale sono utilizzati condensatori in Polipropilene. Amplificazione per cuffia
in comune allo stadio di uscita della sezione pre e utilizzabile con qualsiasi
cuffia elettro-dinamica Risposta in frequenza: DC ~ 100 kHz +/- 0.1dB, massima
tensione di uscita 7Vrms Impedenza di uscita: <30ohms, massima potenza di
uscita: 100mW su 8 ohm/ 300mW su 150Ohm / 150mW su 300Ohm DAC/Power 5 ingressi
digitali, 1- USB, 2 coax, 2 optical , upsampling 24/96 con DAC ESS9006, 11
sezioni di alimentazioni separate con regolatori, trasformatore di
disaccoppiamento per l’ingresso USB per totale isolamento galvanico.
Rapporto S/N: >122db, Jitter < 1picosecond misurato con Master Clock (Super
Clock) Dimensioni: 12,5x35x35cm Finitura: Nero Laccato
It
is not often that new milestones in audio are set: The Nova is one of those rare
products that fit well into this elite category of firsts. Nova should be
considered if you’re looking to improve computer-based or streaming audio to a
“high-end” performance level; or if you just need a "new millennium integrated
amplifier". The Nova is a world class 80wpc integrated amplifier with enough
digital and analog inputs and outputs to satisfy all the new digital devices,
plus, it can handle a few of the old dogs like turntables (w/external phono
preamp), tuners, etc.. It performs much like a high-end integrated amplifier
because that’s what it is. However, this versatile piece also makes a great
pre-amp or with its class A fixed out, a stand-alone DAC that will allow you to
finally add a Mac mini or other computer to your exising system. Or you may want
to take advantage of the out on your cable box... Whether it’s digital or analog,
the Nova is engineered for the way you listen today. Now all the time, effort,
and money you’ve spent ripping CDs and downloading music is rewarded with truly
incredible sound. Even radio stations and compressed MP3 files take on new life
through the Nova. So if you like to rip or download…go for it. If you want to
transfer your music from your comouter to another room, we have you covered. If
it's digital, you pick it, we’ll make it sound great. Amp ST mos-fet amp modules
80w/ch at less than 1% distortion in to 6 ohms Internally wired like Sigma Servo
control (two wires from amp to terminal) for better damping PreAmp Hybrid tube
design (6922) 6.5V output @ 2.0V input <30 Ohms at the output stage Class A
output stage Switching relays in the signal path Polypropylene caps in the
signal path Headphone Amp (shared with the Pre-Out stage) Suitable for all
electro-dynamic headphones Frequency response: DC ~ 100 kHz +/- 0.1dB Voltage
gain: 10dB Maximum output voltage: 7Vrms output impedance: <30ohms Maximum
output power: 100mW into 8Ohm / 300mW into 150Ohm / 150mW into 300Ohm Class A
output stage 6922 Tube is in circuit DAC 5 digital inputs 1- USB, 2
coax, 2 optical 24/96 upsampling ESS9006 DAC 11 regulated power supplies
Organic capacitors Class A output stage Transformer coupled digital Inputs for
ground isolation Galvanically isolated USB stage. >122db S/N
<1picosecond jitter measured at the Master Clock (Super Clock) Size 5” H x
14 ¾” W x 14” D (including volume knob and speaker terminals) Weight
26lbs.
PEACHTREE AUDIO
iDECCO€.1.099,00 Per prezzo
scontato
TELEFONA/ E-MAIL iDecco
Specifications Amp 40 watts per channel <1% distortion into 6 ohms Stereo
MOSFET amp modules Preamp Class A Preamp output stage<30 Ohms output impedance
Hybrid tube design using triode (Stereo 6n1p) 6.5V output @ 2.0V input
Polypropylene caps in the signal path 1 Aux input 4 Digital inputs (all
transformer coupled) iPod, USB, Toslink (optical), Coax Headphone Amp
Class A output with 6n1p tube in the circuit Suitable for all electro-dynamic
headphones Frequency response: DC ~ 100 kHz +/- 0.1dB Voltage gain: 10dB Maximum
output voltage: 7Vrms Output impedance: <30ohms Maximum output power: 100mW into
8 Ohm / 300mW into 150 Ohm / 150mW into 300 Ohm Digital to Analog Converter (DAC)
4 digital inputs: 1 iPod, 1 USB, 1 Coax, 1 Toslink (optical) ESS 9006 Sabre DAC
w/patented jitter reduction circuit 24/96 upsampling 11 regulated
power supplies Class A output stage (for use as an external DAC) Transformer
coupled digital Inputs for ground isolation Galvanically isolated USB stage.
>118db S/N <1 picosecond jitter measured at the Master Clock (Super Clock)
AC 115v/230v switchable from back panel Size 5” H x 14 ¾” W x 14” D (including
volume knob and speaker terminals) Finish Black Gloss Weight 23
pounds Warranty 1 yr parts and labor iDecco Specifications
Amp 40 watts per
channel <1% distortion into 6 ohms Stereo MOSFET amp modules Preamp Class A
Preamp output stage <30 Ohms output impedance Hybrid tube design using
triode (Stereo 6n1p) 6.5V output @ 2.0V input Polypropylene caps in the signal
path 1 Aux input 4 Digital inputs (all transformer coupled) iPod, USB, Toslink (optical),
Coax Headphone Amp Class A output with 6n1p tube in the circuit Suitable
for all electro-dynamic headphones Frequency response: DC ~ 100 kHz +/- 0.1dB
Voltage gain: 10dB Maximum output voltage: 7Vrms Output impedance: <30ohms
Maximum output power: 100mW into 8 Ohm / 300mW into 150 Ohm / 150mW into 300 Ohm
Digital to Analog Converter (DAC) 4 digital inputs: 1 iPod, 1 USB, 1 Coax, 1
Toslink (optical) ESS 9006 Sabre DAC w/patented jitter reduction circuit
24/96 upsampling 11 regulated power supplies Class A output stage (for use as an
external DAC)Transformer coupled digital Inputs for ground isolation
Galvanically isolated USB stage. >118db S/N <1 picosecond jitter measured at the
Master Clock (Super Clock) AC 115v/230v switchable from back panel Size 5” H x
14 ¾” W x 14” D (including volume knob and speaker terminals) Finish Black
Gloss Weight 23 pounds Warranty 1 yr parts and labor
PEACHTREE AUDIO
DECCO2€.
899,00 Per prezzo
scontato
TELEFONA/ E-MAIL Decco
2 is a versatile integrated amplifier with a built-in ESS Sabre DAC. It's
designed for those who use any digital source for music. Computers, Sonos,
Airport Express, Apple TV etc. It's a big improvement over the original, as we
learned much and wanted to further improve the experience. The Decco2 now has
class A outputs for preamp, headphone out and fixed line outs. The Decco2 is
four products in one... 1. 40 watt per channel integrated Amplifier 2. Class A
Tube Preamplifier 3. Stand-Alone Multi-Input DAC 4. Class A Headphone Amplifier
Digital to Analog converter: The heart of the Decco2 is our over performing ESS
Sabre D/A converter. This complete DAC is the result of 2 years in development
and many hours of critical listening. We use the ESS 9006 Sabre DAC for digital
processing. Our design uses a mutli-layer DAC board with over 450 components and
11 regulated power supplies. The ESS Sabre DAC's patented jitter reduction
circuit re-clocks the digital signal before passing it through a high-resolution
24/96 upsampling processor. This is perfect for computers and most streaming or
hard-drive based music servers because most of them have high levels of jitter.
Jitter, simply put, is digital timing error between the source and the DAC. The
lower the jitter, the better the DAC sounds. Our DAC takes the re-clocked signal
and upsamples it to achieve 24/96 resolution. This transforms your iPod or just
about any digital source to the performance of a high-end CD player. Even cheap
transports and high jitter sources like Sonos, computers and iPods now sound
great because the iDecco thinks they're all high-end digital transports! The
iDecco can deliver an astounding 118 dB signal to noise ratio, greatly extending
dynamic range and your overall music experience with virtually all digital
sources. Each digital input is transformer-coupled so noise associated with
ground problems and switching power supplies from computers is eliminated. The
USB connection is galvanically isolated, eliminating noise generated by your
computer's switching power supply and greatly improving sound quality. The
Decco2 is a great stand-alone D/A converter and will drastically improve most
any digital source you have including your old CD player. The Decco 2 has a
fixed Class A line out so it can be used as a “remote switchable D/A converter”
that can be added to any current system, or even your whole-house audio system,
to handle and improve any digital source. If you’re thinking about adding a PC
or Mac, Apple TV, Sonos or any other music server to your system, the iDecco
serves as the perfect upscale D/A converter. The preamp section employs a Class
A tube buffer with a 30-ohm output impedance, so if 40 watts per channel isn't
quite enough power, you can hook up a separate, more powerful amplifier. The
preamp maintains a high level of detail while also taming harsh compressed
digital music and allowing exceptional reproduction when listening to high
resolution files. The Decco 2 has a USB input for your computer, 1 coax, and 1
optical input for other digital sources like Squeezebox, Apple TV or Airport
Express, Sonos, and XM or Sirius tuners. It also has 2 analog inputs for a tape
deck or phono preamp. We tried to think of everything you could possibly need on
a piece like this. The Decco 2 should have you covered! For the headphone user
the Decco2 has a "Class A tube" headphone section that rivals some of the best
headphone amps available today. Many hours were spent on the headphone section
and no detail regarding quality was left to chance. The signal passes through
the DAC, preamp and then the tube buffer giving you an extended yet addictive
sound. When headphones are plugged in, your speakers are muted so you can rock
on when quiet is a necessity. Headphones have never sounded better than through
the iDecco
Legenda istruzioni
Clicca
per qui per vedere : FOTO PRODOTTO
Clicca
per qui per vedere : ISTRUZIONI PRODOTTO
Clicca
per qui per vedere : CATALOGO,PROVA RIVISTE SPECIALIZZATE PRODOTTO
Clicca
per qui per vedere : DATI TECNICI SPECIFICHE
PRODOTTO
Attenzione
Per ordinare o avere
gli ultimi prezzi aggiornati telefona al
0174 670100
o invia un E-mail a info@sinergy.us
Il presente listino
sostituisce ed annulla ogni precedente.I prezzi indicati si
riferiscono a singolo diffusore.
Le caratteristiche e i prezzi indicati possono variare senza
preavviso telefonare o inviare un e-mail per ulteriori domande e
conferme sui prezzi sopra riportati.
Prezzi
franco
nostro magazzino
Nota bene Tutti i marchi citati nel presente listino sono di proprietà e
registrati alle rispettive Case Produttrici
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
.gif)
It
is not often that new milestones in audio are set: The Nova is one of those rare
products that fit well into this elite category of firsts. Nova should be
considered if you’re looking to improve computer-based or streaming audio to a
“high-end” performance level; or if you just need a "new millennium integrated
amplifier". The Nova is a world class 80wpc integrated amplifier with enough
digital and analog inputs and outputs to satisfy all the new digital devices,
plus, it can handle a few of the old dogs like turntables (w/external phono
preamp), tuners, etc.. It performs much like a high-end integrated amplifier
because that’s what it is. However, this versatile piece also makes a great
pre-amp or with its class A fixed out, a stand-alone DAC that will allow you to
finally add a Mac mini or other computer to your exising system. Or you may want
to take advantage of the out on your cable box... Whether it’s digital or analog,
the Nova is engineered for the way you listen today. Now all the time, effort,
and money you’ve spent ripping CDs and downloading music is rewarded with truly
incredible sound. Even radio stations and compressed MP3 files take on new life
through the Nova. So if you like to rip or download…go for it. If you want to
transfer your music from your comouter to another room, we have you covered. If
it's digital, you pick it, we’ll make it sound great. Amp ST mos-fet amp modules
80w/ch at less than 1% distortion in to 6 ohms Internally wired like Sigma Servo
control (two wires from amp to terminal) for better damping PreAmp Hybrid tube
design (6922) 6.5V output @ 2.0V input <30 Ohms at the output stage Class A
output stage Switching relays in the signal path Polypropylene caps in the
signal path Headphone Amp (shared with the Pre-Out stage) Suitable for all
electro-dynamic headphones Frequency response: DC ~ 100 kHz +/- 0.1dB Voltage
gain: 10dB Maximum output voltage: 7Vrms output impedance: <30ohms Maximum
output power: 100mW into 8Ohm / 300mW into 150Ohm / 150mW into 300Ohm Class A
output stage 6922 Tube is in circuit DAC 5 digital inputs 1- USB, 2
coax, 2 optical 24/96 upsampling ESS9006 DAC 11 regulated power supplies
Organic capacitors Class A output stage Transformer coupled digital Inputs for
ground isolation Galvanically isolated USB stage. >122db S/N
<1picosecond jitter measured at the Master Clock (Super Clock) Size 5” H x
14 ¾” W x 14” D (including volume knob and speaker terminals) Weight
26lbs. 
Clicca
per qui per vedere : FOTO PRODOTTO
Clicca
per qui per vedere : DATI TECNICI SPECIFICHE
PRODOTTO